Skip to content
Monday, November 23, 2026
Military News

LUCAS drone: Can it be mass-produced on the battlefield? A $9 million experiment

컨테이너 안에서 로봇 팔이 공격 드론 기체를 제작하는 이동식 제조공장

The container factory is moving forward.

It is small and mobile, more like a workshop than a factory. Machina stated that it would deploy a robotic manufacturing system, measuring 20 feet by 36 feet, close to the battlefield to produce LUCAS attack drones.

That does not mean the U.S. military is now mass-producing LUCAS on the battlefield. What the U.S. Department of Defense commissioned is not the purchase of completed drones, but an 18-month pilot project to determine whether forward production is feasible.

This is not yet a drone factory; it is a factory currently undergoing testing.

The contract amount is $9 million. The core of this project is not the quantity of drones, but the production method. Instead of a traditional central factory and a long supply chain, this is a stage to verify whether manufacturing facilities can be brought to where they are needed.

This agreement does not constitute a mass production license.

The project is being conducted in accordance with the U.S. Department of Defense’s Organic Industrial Base Modernization Challenge. The objective is to deploy Machina’s RoboCraftsman system to a designated location and demonstrate its ability to manufacture the airframe of a LUCAS-class unmanned aerial vehicle at that location.

The initial plan was to establish Edge Factories at two locations within the United States. While the long-term goal includes deployments in forward overseas regions such as Kuwait, the specific locations and timelines have not been disclosed.

A contract for the deployment of 10 or more cells has not yet been finalized. Whether LUCAS will be mass-produced in various regions will also be decided after this testing.

This agreement is not for mass purchases, but rather for verifying production technology.

The exact number of aircraft that must be produced within the 18-month contract has not been disclosed. Therefore, the $9 million cannot be interpreted as the purchase cost for a certain number of LUCAS aircraft. Both pilot factories must successfully complete actual production and quality inspections before the next phase can begin.

One aircraft takes two to five days to produce, but it is not a finished product.

Each Edge Factory consists of one or two RoboCraftsman cells. According to Machina, a single cell can produce one LUCAS aircraft in two to five days, depending on the aircraft’s size.

Although it may appear to be fast, this figure refers to the production rate of metal airframe structures. It does not represent the assembly speed of the entire weapon system, which includes engines, electronic equipment, warheads, and guidance systems.

Aircraft production and finished product production are different.

RoboCraftsman processes metal sheets according to digital designs, without the need for molds or dedicated rollers. Machina explained that metal is used in the LUCAS aircraft because it is cheaper and easier to procure than composite materials, and it can be processed using automated processes.

The size of a fully installed system is 20 feet by 36 feet, and its weight is 120,000 pounds. Contrary to its name, this is not equipment that can simply be placed on site and used. It requires raw materials, electronic components, fuel, skilled personnel, and quality inspection equipment.

Machina has presented a price of $15,000 to $40,000 for the aircraft. This is an estimate based on the complexity of the aircraft. It has not been confirmed whether this is the price of a completed weapons system including weapons, communications equipment, navigation systems, and launch equipment.

The approximate price of a single LUCAS system, as revealed by the U.S. Central Command in 2025, was approximately $35,000. It is not possible to definitively conclude that the Machina aircraft is cheaper based on a simple comparison of these two figures.

Why is the military now trying to produce drones in the forward area?

LUCAS aims to be a low-cost, mass-produced expendable attack drone. It is based on a reverse-engineered design of the Iranian Shahed-136 drone, and its deployment with the U.S. military in the Middle East was first revealed in December 2025.

The U.S. Central Command announced that in December 2025 it had established in the Middle East the first U.S. military squadron of expendable attack drones, composed of LUCAS systems. It subsequently confirmed that LUCAS was used in combat for the first time in an attack operation against Iran in February 2026.

After deployment in actual operations, the issues become different. It is not only about how many drones to purchase, but also about whether replacements can be continuously provided near the operational area even if supply is disrupted.

Forward production is a plan to shorten the supply chain.

Instead of relying on a single central factory and long-distance transportation, distributing production capacity across multiple locations can reduce the risk of a complete production halt if one facility is disrupted. However, this approach increases the burden of defending a larger number of smaller facilities.

Machina explains that by modifying the digital design, it is possible to produce metal structures of different shapes without creating new molds. The software allows users to create and review 20, 30, 40, or 50 different design variations.

Ed Mehr, the founder and CEO of Machina, stated that the company can produce different drones tailored to the specific requirements of each operational area. This production model is closer to adapting the design based on the mission, rather than fixing a single airframe for mass production.

However, the technical verification is not yet complete. Machina built and tested a six-foot-long, half-scale test aircraft at Edwards Air Force Base. The initial design revealed a problem with its response to crosswinds.

It has not been confirmed from publicly available information whether the problem has been resolved, or whether the revised design has passed flight testing.

Expectations and risks increase together.

The U.S. Central Command and forward operational units expect the following benefits. Deploying inexpensive, single-use attack drones near the operational area can reduce logistical delays and inventory shortages.

At the time, General Bradley Cooper, then commander of U.S. Central Command, described LUCAS as “indispensable.” However, this contract does not immediately mean that its capabilities will be scaled up to mass production levels.

For American taxpayers, this project represents an investment in the production system. The $9 million is not for purchasing finished products, but for testing whether it is possible to manufacture drones near the front lines. If successful, additional defense funding may be required; if unsuccessful, it may not lead to mass production.

This contract represents the initial cost, not the final invoice.

Forward manufacturing facilities can reduce supply lines. However, they also increase the risk of exposure to attacks and sabotage for the facilities and personnel. Decentralized production reduces the risk concentrated in a single location, but it can increase the number of facilities that need to be protected.

Replenishing attack drones more quickly could enhance the U.S. military’s ability to sustain operations. At the same time, it could also increase the frequency and scale of drone attacks. While this issue may not directly and immediately affect ordinary consumers’ living expenses, it could affect defense spending, security, and how wars are sustained.

What has been confirmed is the pilot plant; what remains unknown is the performance report from the battlefield.

The confirmed fact is that Machina is responsible for a containerized system demonstration project for LUCAS production. Initially, the plan is to install Edge Factories at two locations in the continental United States.

According to Machina, a single RoboCraftsman unit can produce one LUCAS aircraft in two to five days. The actual number of aircraft to be produced under the contract has not been disclosed.

This project represents a separate production path and does not involve cooperation with SpektreWorks, the company that manufactured the existing LUCAS airframes. However, there is no basis to conclude that Machina will replace SpektreWorks. It remains to be confirmed whether the airframes produced by Machina will replace the existing airframes or be operated as a separate LUCAS variant.

The possibility of producing thousands or tens of thousands of units, as mentioned by Machina, is not guaranteed by this contract. This is an explanation from the company, based on the number of RoboCraftsman systems that are ordered.

It has not yet been verified whether the same quality and production speed can be maintained under electronic warfare, climate, and security conditions in the combat zone. Whether the crosswind response issues revealed in the initial testing have been resolved has not been disclosed.

The next step is not the announcement of mass production, but rather the verification of the performance of the two pilot plants.

Therefore, the answer to the question is straightforward. The U.S. military has not yet been able to mass-produce the LUCAS directly on the battlefield. Currently, they are testing whether it is possible to manufacture the aircraft near the front lines, and whether that method can be integrated into the actual logistics system.

If the testing is successful, there will be options to divide the production facilities across multiple regions. However, the deployment of facilities overseas and subsequent large-scale production contracts have not yet been decided. The success of this project will be evaluated not by the size of the containers, but by the production quality and on-site maintenance capabilities.

Frequently Asked Questions.

Will the LUCAS drones be mass-produced directly at the front lines as a result of this contract?

Not yet. This contract is for a 18-month pilot project at two Edge Factory locations to demonstrate the feasibility of production. Whether mass production is possible in other regions will be determined later.

How many LUCAS drones can $9 million buy?

This is not the cost for the mass purchase of completed drones. This is the contract amount for establishing a production system in the forward area and verifying the technology.

Does the RoboCraftsman cell produce one complete LUCAS unit in two to five days?

Machina stated that a single cell can produce one LUCAS airframe in two to five days. However, this description pertains only to the production of metal airframes and does not include the overall production rate of the entire weapon system, which includes engines, electronic equipment, warheads, and guidance systems.

Does Machina replace the existing LUCAS manufacturer, SpektreWorks?

This is not a confirmed fact. Machina’s business is a separate production line that does not cooperate with SpektreWorks. It is not yet confirmed whether it will replace existing aircraft or be operated as a separate LUCAS variant.

Where are the forward factories located?

The initial two locations are planned to be installed in the continental United States. The exact locations have not been disclosed. While deployment to forward areas overseas, such as Kuwait, has been mentioned as a goal, it has not been confirmed.

Has the follow-up mass production contract been finalized?

Not yet. The use of expanded deployments with 10 or more cells, and the feasibility of mass production in various regions, will be determined after this 18-month testing period.

DEFENSE DIGEST Editorial Team
Facebook X (Twitter) Copy link